Airworthiness Directives; Viking Air Limited Model DHC-3 (Otter) Airplanes
Requires incorporating revised airspeed limitations and marking the airspeed indicator accordingly.
[Federal Register Volume 76, Number 106 (Thursday, June 2, 2011)]
[Rules and Regulations]
[Pages 31800-31803]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2011-13532]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2011-0543; Directorate Identifier 2011-CE-018-AD;
Amendment 39-16709; AD 2011-12-02]
RIN 2120-AA64
Airworthiness Directives; Viking Air Limited Model DHC-3 (Otter)
Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for the
products listed above that are equipped with a Honeywell TPE331-10 or -
12JR turboprop engine installed per Supplemental Type Certificate (STC)
SA09866SC. This AD requires incorporating revised airspeed limitations
and marking the airspeed indicator accordingly. There is also a
requirement for the installation of a temporary placard until the
airspeed indicator can be modified but not to
[[Page 31801]]
exceed a certain period of time. This AD was prompted by analysis that
showed that airspeed limitations for the affected airplanes are not
adjusted for the installation of a turboprop engine as stated in the
regulations. We are issuing this AD to prevent the loss of airplane
structural integrity due to the affected airplanes being able to
operate at speeds that exceed the speeds established in the Federal
aviation regulations for safe operation.
DATES: This AD is effective June 2, 2011.
We must receive comments on this AD by July 18, 2011.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The street address for
the Docket Office (phone: 800-647-5527) is in the ADDRESSES section.
Comments will be available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Peter W. Hakala, Aerospace Engineer,
FAA Rotorcraft Directorate, Fort Worth Special Certification Office,
ASW-190, FAA, 2601 Meacham Blvd., Fort Worth, Texas 76137; phone: (817)
222-5145; fax: (817) 222-5785; e-mail: [email protected].
SUPPLEMENTARY INFORMATION:
Discussion
Recent analysis by the FAA on the Viking Air Limited Model DHC-3
(Otter) airplanes equipped with a Honeywell TPE331-10 or -12JR
turboprop engine installed per Supplemental Type Certificate (STC)
SA09866SC revealed that airspeed limitations for the affected airplanes
are not adjusted for the installation of a turboprop engine as stated
in the regulations. 14 CFR 23.1505 paragraph (c) applies to turbine
engine airplanes and includes the following: ``* * * a maximum
operating limit speed (VMO/MMO-airspeed or Mach number, whichever is
critical at a particular altitude) must be established as a speed that
may not be deliberately exceeded in any regime of flight (climb,
cruise, or descent) unless a higher speed is authorized for flight test
or pilot training operations. VMO/MMO must be established so that it is
not greater than the design cruising speed VC/MC and so that it is
sufficiently below VD/MD and the maximum speed shown under 23.251 to
make it highly improbable that the latter speeds will be inadvertently
exceeded in operations. The speed margin between VMO/MMO and VD/MD or
the maximum speed shown under 23.251 may not be less than the speed
margin established between VC/MC and VD/MD under 23.335(b), or the
speed margin found necessary in the flight test conducted under
23.253.''
The FAA has discovered that the affected airplanes, as currently
certificated, have airspeed indicators with color band markings that do
not comply with 14 CFR 23.1505(c). This could result in reduced safety
margins that may result in an unsafe condition.
Based on further analysis with application of the regulations, the
FAA has determined that an airspeed limitation of 134 miles per hour
(mph) for airplanes with floats and 144 mph for basic land airplanes
would address the concern for the unsafe condition.
This condition, if not corrected, could result in loss of airplane
structural integrity due to the affected airplanes being able to
operate at speeds that exceed the speeds established in the Federal
aviation regulations for safe operation.
FAA's Determination
We are issuing this AD because we evaluated all the relevant
information and determined the unsafe condition described previously is
likely to exist or develop in other products of the same type design.
AD Requirements
This AD requires incorporating revised airspeed limitations and
marking the airspeed indicator accordingly. There is also a requirement
for the installation of a temporary placard until the airspeed
indicator can be modified but not to exceed a certain period of time.
FAA's Justification and Determination of the Effective Date
An unsafe condition exists that requires the immediate adoption of
this AD. The FAA has found that the risk to the flying public justifies
waiving notice and comment prior to adoption of this rule because it
could result in loss of airplane structural integrity due to the
affected airplanes being able to operate at speeds that exceed the
speeds established in the Federal aviation regulations for safe
operation. Therefore, we find that notice and opportunity for prior
public comment are impracticable and that good cause exists for making
this amendment effective in less than 30 days.
Comments Invited
This AD is a final rule that involves requirements affecting flight
safety and was not preceded by notice and an opportunity for public
comment. However, we invite you to send any written data, views, or
arguments about this AD. Send your comments to an address listed under
the ADDRESSES section. Include the docket number FAA-2011-0543 and
Directorate Identifier 2011-CE-018-AD at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this AD. We will
consider all comments received by the closing date and may amend this
AD because of those comments.
We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this AD.
Costs of Compliance
We estimate that this AD affects 25 airplanes of U.S. registry
We estimate the following costs to comply with this AD:
[[Page 31802]]
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Action Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
Airplane Flight Manual Limitation, 10 work-hours x $85 per $90 $940 $23,500
Placard, and Airspeed Indicator hour = $850.
Modification.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation Programs''
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
subtitle VII, part A, subpart III, section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2011-12-02 Viking Aircraft Limited: Amendment 39-16709; Docket No.
FAA-2011-0543; Directorate Identifier 2011-CE-018-AD.
Effective Date
(a) This AD is effective June 2, 2011.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Viking Aircraft Limited Model DHC-3
(Otter) airplanes, all serial numbers, that are:
(1) equipped with a Honeywell TPE331-10 or -12JR turboprop
engine installed per Supplemental Type Certificate (STC) SA09866SC
(Texas Turbines Conversions, Inc.); and
(2) certificated in any category.
Subject
(d) Joint Aircraft System Component (JASC)/Air Transport
Association (ATA) of America Code: 11, Placards and Markings.
Unsafe Condition
(e) This AD was prompted by analysis that showed that airspeed
limitations for the affected airplanes are not adjusted for the
installation of a turboprop engine as stated in the regulations. We
are issuing this AD to prevent of the loss of airplane structural
integrity due to the affected airplanes being able to operate at
speeds that exceed the speeds established in the Federal aviation
regulations for safe operation.
Compliance
(f) Comply with this AD within the compliance times specified,
unless already done.
Table 1--Actions, Compliance, and Procedures
----------------------------------------------------------------------------------------------------------------
Actions Compliance
----------------------------------------------------------------------------------------------------------------
(1) Insert the following information into the Limitations section of the airplane Before further flight after
flight manual (AFM) or AFM supplement: ``Airspeed limitation: VMO = 144 MPH for the effective date of this
land/ski plane and VMO = 134 MPH for seaplane.'' AD.
(i) This can be done by inserting this AD into the Limitations section of the
AFM or AFM supplement.
(ii) Inserting the information into the Limitations section of the AFM or AFM
supplement may be performed by the owner/operator (pilot) holding at least a
private pilot certificate and must be entered into the aircraft records
showing compliance with this AD in accordance with 14 CFR Sec. Sec. 43.9
(a)(1)-(4) and 14 CFR 91.417(a)(2)(v). The record must be maintained as
required by 14 CFR Sec. Sec. 91.417, 121.380, or 135.439.
(2) Fabricate a placard using letters of at least \1/8\-inch in height with the Within the next 10 hours time-
following words: ``Never exceed airspeed of 144 MPH, VMO speed limit for land/ in-service (TIS) after the
ski plane and 134 MPH, VMO speed limit for seaplane.'' Install this placard on effective date of this AD.
the airplane instrument panel next to the airspeed indicator within the pilot's
clear view.
(3) Modify the airspeed indicator accordingly to reflect the above limitation. Within the next 30 days after
Mark the airspeed indicator with a red radial line at 144 MPH for a land/ski the effective date of this
plane and/or with a red radial at 134 MPH for a seaplane. This instrument AD.
modification must be done by an appropriately rated repair facility.
(i) This action eliminates the need for the placard required by paragraph
(f)(2) above.
(ii) This action can be done instead of the placard requirement in paragraph
(f)(2) provided it is done within the next 10 hours TIS after the effective
date of this AD.
----------------------------------------------------------------------------------------------------------------
[[Page 31803]]
Alternative Methods of Compliance (AMOCs)
(g)(1) The Manager, Fort Worth Special Certification Office,
FAA, has the authority to approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19. In accordance with 14
CFR 39.19, send your request to your principal inspector or local
Flight Standards District Office, as appropriate. If sending
information directly to the manager of the ACO, send it to the
attention of the person identified in the Related Information
section of this AD.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
Related Information
(h) For more information about this AD, contact Peter W. Hakala,
Aerospace Engineer, FAA Rotorcraft Directorate, Fort Worth Special
Certification Office, ASW-190, FAA, 2601 Meacham Blvd., Fort Worth,
Texas 76137; phone: (817) 222-5145; fax: (817) 222-5785; e-mail:
[email protected].
Issued in Kansas City, Missouri, on May 25, 2011.
Earl Lawrence,
Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 2011-13532 Filed 6-1-11; 8:45 am]
BILLING CODE 4910-13-P
Sources. Section 1 is written by AircraftDirectives from the record below and is a reading aid only. Section 2 is the United States Government's own text, reproduced without edit.
Federal Register: https://www.federalregister.gov/documents/2011/06/02/2011-13532/airworthiness-directives-viking-air-limited-model-dhc-3-otter-airplanes
Official PDF: https://www.govinfo.gov/content/pkg/FR-2011-06-02/pdf/2011-13532.pdf
Packet generated 2026-08-18 08:16 UTC.
This packet is not an airworthiness determination and not legal or maintenance advice. AircraftDirectives reproduces official records and condenses their wording for easier reading. It does not decide, certify or imply whether any aircraft, engine, appliance or part is airworthy, compliant, affected by this directive, or eligible for return to service. No inspection, approval, or determination of any kind is performed or implied by this document.
Section 1 is a reading aid, not the rule. It is our own plain-language condensation, written to help a reader find the relevant directive quickly. It is NOT a substitute for the regulation, it may omit conditions, exceptions, compliance times, alternative methods of compliance (AMOCs) and applicability limits, and it has no legal force whatsoever. Only the official text governs. Where Section 1 and Section 2 differ in any respect, Section 2 - and the official source it was retrieved from - controls absolutely.
Responsibility remains with the owner/operator. Under 14 CFR §91.403 and §91.417 the owner or operator is responsible for maintaining airworthiness and for required records; under §39.7 no person may operate a product to which an airworthiness directive applies except in accordance with that directive. Determining applicability to a specific serial number and configuration, and performing or supervising any required action, is the responsibility of the owner/operator and appropriately certificated personnel.
Accuracy and currency. Section 2 was retrieved at the time stamped above and is reproduced without edit; Federal Register material is a work of the United States Government. Directives are amended, corrected and superseded over time, and this sheet is a snapshot, not a live record - it does not update after printing. Re-check the official sources before acting on it. This packet is provided without warranty of any kind, express or implied, including fitness for a particular purpose. We do not sell parts and have no commercial interest in any action a directive may require.