Airworthiness Directive

AD 96-24-09 61 FR 59828 Superseded

Federal Aviation Administration · 14 CFR part 39

Requires replacing the engine main electrical harness assembly with an improved assembly, disabling the overspeed solenoid, inspecting the engine control unit (ECU) internal PW10 voltage to determine electrical noise…

FR document
96-29861
Published
1996-11-25
Effective
1996-11-25
Models covered
1

Last live check: 2026-11-14

This page is a reference Record, not an airworthiness or compliance determination. Read the full notice.

AD

96-24-09

FR doc 96-29861 · 61 FR 59828

AD 96-24-09Published 1996-11-25Effective 1996-11-25

Superseded by 97-21-09

Supersedence is read from the Federal Register text of the newer AD — the FAA publishes no structured field for it — and names only ADs held in our index.

FAA rule - 14 CFR 39

FAA rule. Compliance with an applicable AD is required under 14 CFR 39.7. Check its effective date, applicability, compliance times and current status.

Requires replacing the engine main electrical harness assembly with an improved assembly, disabling the overspeed solenoid, inspecting the engine control unit (ECU) internal PW10 voltage to determine electrical noise characteristics, and replacing units not considered serviceable.

Supersedes an earlier directive that is not in our index. See the official text.

Why this AD
Prompted by investigation into the causes of the inflight engine shutdowns.
Applies to
Allison Engine Company Model 250-C47B Turboshaft Engines · 1 model in our index, listed below
Superseded by
97-21-09
Full official abstract

This amendment adopts a new airworthiness directive (AD) that is applicable to Allison Engine Company Model 250-C47B turboshaft engines. This action supersedes priority letter AD 96-21-12, applicable to Bell Helicopter Textron, A Division of Textron Canada Ltd. (BHTC) Model 407 helicopters, that currently prohibits further flight, due to uncommanded inflight engine shutdowns. This action requires replacing the engine main electrical harness assembly with an improved assembly, disabling the overspeed solenoid, inspecting the engine control unit (ECU) internal PW10 voltage to determine electrical noise characteristics, and replacing units not considered serviceable. In addition, this AD requires adding a placard to the helicopter instrument panel notifying the pilot that the overspeed protection system is disabled and removes a placard which was required by priority letter AD 96-21-12; revises the BHTC Model 407 Rotorcraft Flight Manual (RFM); and requires maintenance actions to clear the engine electronic control unit (ECU) of faults prior to each flight. Accomplishment of these actions will enable operators to resume flight operations. This amendment is prompted by investigation into the causes of the inflight engine shutdowns. The actions specified by this AD are intended to prevent uncommanded inflight engine shutdowns, which can result in autorotation, forced landing, and possible loss of the helicopter.

More directives for Bell 407

  1. AD 2026-14-07 Airworthiness Directives; Bell Textron Canada Limited Helicopters Effective 2026-08-21
  2. AD 2026-10-04 Airworthiness Directives; Bell Textron Canada Limited Helicopters Effective 2026-06-25
  3. AD 2025-13-01 Airworthiness Directives; Bell Textron Canada Limited Helicopters Effective 2025-07-08
  4. AD 2024-10-12 Airworthiness Directives; Bell Textron Canada Limited Helicopters Effective 2024-08-22
  5. AD 2023-17-51 Airworthiness Directives; Bell Textron Canada Limited Helicopters Effective 2023-09-21

All Bell 407 directives

Applies to 1 model in our index

This page is a reference Record, not an airworthiness or compliance determination. Official FAA and manufacturer sources control over our restatement, subject to governing law. Check applicability, current requirements and incorporated documents before acting. The owner or operator remains responsible for airworthiness and required records under 14 CFR 91.403 and 91.417, as applicable. Terms of Use: /terms.