Airworthiness Directive

AD 2005-03-10 70 FR 7167 Active

Federal Aviation Administration · 14 CFR part 39

Requires a visual check of each main rotor grip (grip) and pitch horn assembly without disassembling the main rotor hub assembly (hub assembly), and a visual inspection at specified intervals of each affected grip and pitch horn…

FR document
05-2609
Published
2005-02-11
Effective
2005-03-18
Models covered
2

Last live check: 2026-11-15

This page is a reference Record, not an airworthiness or compliance determination. Read the full notice.

AD

2005-03-10

FR doc 05-2609 · 70 FR 7167

AD 2005-03-10Published 2005-02-11Effective 2005-03-18

Supersedes 2002-08-54

Supersedence is read from the Federal Register text of the newer AD — the FAA publishes no structured field for it — and names only ADs held in our index.

FAA rule - 14 CFR 39

FAA rule. Compliance with an applicable AD is required under 14 CFR 39.7. Check its effective date, applicability, compliance times and current status.

Requires a visual check of each main rotor grip (grip) and pitch horn assembly without disassembling the main rotor hub assembly (hub assembly), and a visual inspection at specified intervals of each affected grip and pitch horn assembly for a crack using a 10-power or higher magnifying glass.

Why this AD
Prompted by the determination that an additional enhanced inspection is needed to ensure the integrity of the hub assembly.
Applies to
Bell Helicopter Textron, A Division of Textron Canada Model 222, 222B, 222U and 230 Helicopters · 2 models in our index, listed below
Supersedes
2002-08-54
Full official abstract

This amendment supersedes an existing airworthiness directive (AD) for Bell Helicopter Textron, A Division of Textron Canada (BHTC) Model 222, 222B, 222U, and 230 helicopters, that currently requires a visual check of each main rotor grip (grip) and pitch horn assembly without disassembling the main rotor hub assembly (hub assembly), and a visual inspection at specified intervals of each affected grip and pitch horn assembly for a crack using a 10-power or higher magnifying glass. If a crack is found, the existing AD requires replacing each unairworthy grip or pitch horn with an airworthy part before further flight. This amendment requires those same actions, and also requires an additional inspection of the grip and pitch horn assembly for a crack in the disassembled hub assembly, and replacing any cracked part with an airworthy part. This amendment is prompted by the determination that an additional enhanced inspection is needed to ensure the integrity of the hub assembly. The actions specified by this AD are intended to prevent failure of the grip or pitch horn and subsequent loss of control of the helicopter.

More directives for Bell 222

  1. AD 2026-17-51 Airworthiness Directives; Bell Textron Canada Limited Helicopters Effective 2026-09-14
  2. AD 2021-19-01 Airworthiness Directives; Bell Textron Canada Limited Helicopters Effective 2021-10-13
  3. AD 2016-08-17 Airworthiness Directives; Bell Helicopter Textron Canada Helicopters Effective 2016-05-31
  4. AD 2013-18-06 Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) ... Effective 2013-10-17
  5. AD 2010-26-51 Airworthiness Directives; Bell Helicopter Textron Canada Limited (BHTC) ... Effective 2011-03-25

All Bell 222 directives

Applies to 2 models in our index

This page is a reference Record, not an airworthiness or compliance determination. Official FAA and manufacturer sources control over our restatement, subject to governing law. Check applicability, current requirements and incorporated documents before acting. The owner or operator remains responsible for airworthiness and required records under 14 CFR 91.403 and 91.417, as applicable. Terms of Use: /terms.