Cessna 182

Airworthiness Directives; Textron Aviation Inc. (Type Certificate Previously Held by Cessna Aircraft Company) Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Textron Aviation Inc. Model 182Q and 182R airplanes. This AD was prompted by reports of damaged intercooler inlet and outlet hoses. This AD requires repetitive visual inspections of the intercooler inlet and outlet hoses for cracks and, at a certain compliance time or if any cracks are found, replacement of the intercooler inlet and outlet hoses. The FAA is issuing this AD to address the unsafe condition on these products.

Airworthiness Directives; Textron Aviation Inc. Airplanes

The FAA is adopting a new airworthiness directive (AD) for all Textron Aviation Inc. (Textron) Models 180, 180A, 180B, 180C, 180D, 180E, 180F, 180G, 180H, 180J, 180K, 182, 182A, 182B, 182C, 182D, 185, 185A, 185B, 185C, 185D, 185E, A185E, and A185F airplanes. This AD was prompted by a report of cracks found in the tailcone and horizontal stabilizer attachment structure. This AD requires inspecting the tailcone and horizontal stabilizer for corrosion and cracks and repairing or replacing damaged parts as necessary. The FAA is issuing this AD to address the unsafe condition on these products.

Airworthiness Directives; Textron Aviation Inc. Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Textron Aviation Inc. (Textron) Model 172N, 172P, 172Q, 172RG, F172N, F172P, FR172K, R172K, 182E, 182F, 182G, 182H, 182J, 182K, 182L, 182M, 182N, 182P, 182Q, 182R, T182, F182P, F182Q, FR182, R182, TR182, 206, P206, P206A, P206B, P206C, P206D, P206E, TP206A, TP206B, TP206C, TP206D, TP206E, U206, U206A, U206B, U206C, U206D, U206E, U206F, U206G, TU206A, TU206B, TU206C, TU206D, TU206E, TU206F, TU206G, 207, 207A, T207, T207A, 210-5 (205), 210-5A (205A), 210B, 210C, 210D, 210E, 210F, and T210F airplanes. This AD was prompted by cracks found in the lower area of the forward cabin doorpost bulkhead. This AD requires repetitively inspecting the lower area of the forward cabin doorposts at the strut attach fitting for cracks and repairing any cracks. The FAA is issuing this AD to address the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company Airplanes

We are superseding AD 2000-04-01 that applies to certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H airplanes. AD 2000-04-01 currently requires an inspection of the engine oil pressure switch and, if applicable, replacement of the engine oil pressure switch. This AD increases the applicability of the AD, places a life-limit of 3,000 hours time-in- service on the engine oil pressure switch, and requires replacement when the engine oil pressure switch reaches its life limit. This AD was prompted by new reports of internal failure of the engine oil pressure switch, which could result in complete loss of engine oil with consequent partial or complete loss of engine power or fire. We are issuing this AD to correct the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company Models 150, 152, 170, 172, 175, 177, 180, 182, 185, 188, 190, 195, 206, 207, 210, T303, 336, and 337 Airplanes

We are superseding an existing airworthiness directive (AD) for Cessna Aircraft Company (Cessna) 150, 152, 170, 172, 175, 177, 180, 182, 185, 188, 190, 195, 206, 207, 210, T303, 336, and 337 series airplanes. That AD currently requires repetitive inspections and replacement of parts, if necessary, of the seat rail and seat rail holes; seat pin engagement; seat rollers, washers, and axle bolts or bushings; wall thickness of roller housing and the tang; and lock pin springs. This new AD requires retaining all of the actions from the previous AD and adding steps to the inspection procedures in the previous AD. This AD was prompted by added steps to the inspection procedures, added revised figures, and clarification of some of the existing steps. We are issuing this AD to prevent seat slippage or the seat roller housing from departing the seat rail, which may consequently cause the pilot/copilot to be unable to reach all the controls. This failure could lead to the pilot/copilot losing control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Models 182Q and 182R Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 182Q and 182R airplanes that are equipped with Societ[eacute] de Motorisations A[eacute]ronautiques (SMA) Aircraft Diesel Engine (ADE) Model SR305-230-1 or Model SR305-230 converted to Model SR305-230-1 installed under Supplemental Type Certificate (STC) SA03302AT. This AD requires you to remove the intercooler and the intercooler inlet and outlet hoses, install a reworked intercooler and new intercooler inlet and outlet hoses, inspect hoses and clamp torques, repetitively inspect installation of the intercooler outlet and inlet hose assemblies for any displacement or damage of clamps or hoses, and, if necessary, replace any damaged clamps or hoses. This AD results from a report of two instances of induction hose disconnection occurring while in service, resulting in a loss of turbo boost and a significant loss of engine power. We are issuing this AD to detect and correct improper intercooler outlet and intercooler inlet hose assembly installations, which could result in loss of turbo boost and a significant loss of engine power. This failure could lead to an inability to maintain constant altitude in flight.

Airworthiness Directives; Cessna Aircraft Company 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 Series Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD also requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of airplanes found with alternate static air source selector valve port obstruction caused by improper installation of the part number identification placard. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Airworthiness Directives; Cessna Aircraft Company 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 Series Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of improper installation of the part number identification placard on the alternate static air source selector valve. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Airworthiness Directives; Cessna Aircraft Company 172, 182, and 206 Series Airplanes

The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 182, and 206 series airplanes. This AD requires you to remove the crew seats, modify the seat base/ back attach brackets, and reinstall the seats of the affected airplanes. This AD results from reports of the seat base/back attach bracket failing where it is welded to the seat base. We are issuing this AD to prevent failure of the seat base/back attach brackets, which could result in the seats collapsing backwards during flight with consequent loss of control.

Airworthiness Directives; Cessna Aircraft Company 172 and 182 Series Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company 172 series airplanes with the BRS-172 Parachute System installed via Supplemental Type Certificate (STC) No. SA01679CH and Cessna Aircraft Company 182 series airplanes that are equipped with the BRS-182 Parachute System installed via STC No. SA01999CH. This AD requires you to replace the pick-up collar support and nylon screws for the BRS-172 and BRS-182 Parachute System. This AD results from notification by Ballistic Recovery Systems, Inc. (BRS) that the pick-up collar assembly may prematurely move off the launch tube and adversely affect rocket trajectory during deployment. We are issuing this AD to prevent premature separation of the collar, which could result in the parachute failing to successfully deploy.

Airworthiness Directives; Cessna Aircraft Company Models 182H, 182J, 182K, 182L, 182M, 182N, 182P, 182Q, and 182R Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Model 182 series airplanes that are equipped with Air Plains Services Corporation Supplemental Type Certificate (STC) SA00152WI. This AD requires you to disconnect or remove the electrical cable between the forward ground power relay and the starter relay, install a placard, inspect the fuel line between the auxiliary electric fuel pump and the engine-driven fuel pump for chafing, and replace the fuel line if chafing is found. This AD results from a report of an in-flight and post-landing engine compartment fire. We are issuing this AD to detect and correct interference between the ground power electrical cable, the fuel strainer cable, and the fuel line between the auxiliary electric fuel pump and the engine-driven fuel pump. This condition could lead to a fire in the engine compartment.

Airworthiness Directives; Cessna Aircraft Company Models 172R, 172S, 182T, T182T, 206H, and T206H Airplanes

The FAA is adopting a new airworthiness directive (AD) to supersede AD 2006-17-04, which applies to certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. AD 2006-17-04 currently requires you to inspect the two end fittings on each of the flexible fuel hoses located in the engine compartment for the correct torque values, and, if any incorrect torque values are found during the inspection, tighten the hose end fittings to the correct torque values. This AD results from four reports of loose fuel lines connected to the fuel servo or fuel flow transducer. Two reports were of in-flight engine failure on a Model T182T airplane. A third report was of in-flight engine failure on a Model 206H airplane. A fourth report was of a Model 172S airplane losing engine power on final approach. Consequently, this AD would require you to establish the correct torque values of the end fittings on fuel hoses for certain Cessna Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. This AD clarifies that the torque values need to be physically established and visual inspection only is not sufficient. We are issuing this AD to detect and correct potential loss of fuel flow, which may result in partial or complete loss of engine power and/or uncontrolled engine compartment fire due to fuel leakage forward of the firewall.

Airworthiness Directives; Cessna Aircraft Company Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H Airplanes

The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H airplanes. This AD requires you to install Modification Kit MK172-25-10C or a steel lock rod/bar on both crew seat back cylinder lock assemblies. If a steel lock rod/bar has already been installed on the crew seat back cylinder lock assembly, no further action is required. If you have already installed Modification Kit MK172-25-10A or MK172-25-10B, this AD requires you to do an installation inspection and correct any discrepancies found. This AD results from reports of the crew seat back cylinder lock assembly failing at the aft end and other cylinder lock assemblies found cracked. We are issuing this AD to prevent the crew seat back cylinder lock assembly from bending, cracking, or failing. This failure could cause uncontrolled movement of the seat back, resulting in possible backward collapse during flight. Backward collapse of either crew seat back could result in an abrupt pitch-up if the affected crew member continues to hold on to the control yoke during this failure and could cause difficulty in exiting the airplane from an aft passenger seat after landing.

Airworthiness Directives; Cessna Aircraft Company Models 172R, 172S, 182T, T182T, 206H, and T206H Airplanes

The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. This AD requires you to inspect any MC01-3A I.C. 9 or MC01-3A I.C. 10 main electrical power junction box circuit breakers for correct amperage (amp) (a correct 40-amp circuit breaker) and replace any incorrect amp circuit breaker with the correct 40-amp circuit breaker. This AD results from several reports of circuit breakers that are not the correct 40-amp circuit breaker installed in the MC01-3A main electrical power junction box. We are issuing this AD to replace any incorrect circuit breaker installed in the MC01-3A I.C. 9 or MC01-3A I.C. 10 main electrical power junction box, which could result in premature tripping of the power junction box main feeder circuit breakers and could lead to partial or complete loss of all electrical power on the airplane. This condition could lead to the loss of all navigation and communication equipment and lighting in the cockpit.

Airworthiness Directives; The Cessna Aircraft Company Models 172R, 172S, 182T, and T182T Airplanes

The FAA is adopting a new airworthiness directive (AD) to revise emergency AD 2005-05-53 for The Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, and T182T airplanes. This AD contains the same information as emergency AD 2005-05-53 R1 and publishes the action in the Federal Register. It requires you to do a one-time detailed inspection of the flight control system, correct installations that do not conform to type design, and repair any damage. This AD is the result of flight control system problems found on airplanes within Cessna's control that could also exist on airplanes produced and delivered within a certain time period. We are issuing this AD to prevent loss of airplane control due to incorrect or inadequate rigging of critical flight systems.

Airworthiness Directives; Cessna Aircraft Company 120, 140, 140A, 150, F150, 170, 172, F172, FR172, P172D, 175, 177, 180, 182, 185, A185E, 190, 195, 206, P206, U206, TP206, TU206, 207, T207, 210, T210, 336, 337, and T337 Series Airplanes

The FAA adopts a new airworthiness directive (AD) that will supersede AD 86-26-04, which applies to certain Cessna Aircraft Company (Cessna) 120, 140, 140A, 150, F150, 170, 172, F172, FR172, P172D, 175, 177, 180, 182, 185, A185E, 190, 195, 205, 205A, 206, P206, P206E, TP206A, TU206, TU206E, U206, U206E, 207, T207, 210, T210, 336, 337, and T337 series airplanes. AD 86-26-04 currently requires you to inspect and, if necessary, modify the pilot/co-pilot upper shoulder harness adjusters that have certain Cessna accessory kits incorporated. This AD is the result of reports that additional airplanes have the same unsafe condition and the manufacturer revised the service information to add these airplanes and correct the part number of the shoulder harness adjusters. Consequently, this AD retains the actions of 86-26-04, adds additional airplanes to the applicability section of this AD, and incorporates the revised service information. We are issuing this AD to prevent slippage of the pilot/co-pilot shoulder harness, which could result in failure of the shoulder harness to maintain proper belt length adjustment and tension. Such failure could result in pilot/co- pilot injury.

Airworthiness Directives; Cessna Aircraft Company Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H Airplanes

The FAA supersedes Airworthiness Directive (AD) 2003-24-13, which applies to certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H airplanes that are equipped with a certain Honeywell KAP 140 autopilot computer system installed on the center instrument control panel near the throttle. AD 2003-24-13 currently requires you to install an update to the operating software of certain KAP 140 autopilot computer system, change the unit's part number, and change the software modification identification tab. This AD is the result of the FAA inadvertently omitting four affected Honeywell KAP 140 autopilot computer system part numbers and an affected airplane serial number from the applicability section of AD 2003-24-13. This AD retains the actions required in AD 2003-24-13, corrects the applicability section, and incorporates a revised installation bulletin issued by Honeywell.

Airworthiness Directives; Cessna Aircraft Company 150, 152, 172, 177, 180, 182, 185, 188, 206, 207, 210, and 337 Series Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to Cessna Aircraft Company (Cessna) 150, 152, 172, 177, 180, 182, 185, 188, 206, 207, 210, and 337 series airplanes. This AD requires measuring the visible length of standpipe (tube) in the top assembly of the fuel strainer assembly for the correct length, and replacing any fuel strainer assembly that does not have the correct length of standpipe. This AD is the result of reports that the fuel strainer assemblies on the affected airplanes were manufactured with the fuel standpipes incorrectly installed in the assembly housing top. The actions specified by this AD are intended to prevent foreign material from entering the fuel system and engine, which could result in loss of engine power or complete engine stoppage during flight.

Airworthiness Directives; Cessna Aircraft Company Model 182S Airplanes

This amendment supersedes Airworthiness Directive (AD) 98-13- 10, which currently requires repetitively inspecting all engine exhaust muffler end plates (four total) for cracks on all Cessna Aircraft Company (Cessna) Model 182S airplanes, and replacing any muffler where an end plate is found cracked. AD 98-13-10 also requires fabricating and installing a placard that specifies immediate inspection of all engine exhaust muffler end plates any time the engine backfires upon start-up. This AD is the result of Cessna developing an improved design exhaust system for the Model 182S airplanes. This AD retains the actions of AD 98-13-10 on all affected airplanes, and requires replacing the exhaust system with an improved design exhaust system within a certain period of time, as terminating action for those requirements retained from AD 98-13-10. This AD also limits the effectivity to exclude those airplanes manufactured with the improved design exhaust system. The actions specified by this AD are intended to detect and correct damage to the engine exhaust mufflers caused by cracking and the high stresses imposed on the attachment of the exhaust system at the area the firewall, which could result in exhaust gases entering the airplane cabin with consequent crew and passenger injury.

Airworthiness Directives; Cessna Aircraft Company 180, 182, and 185 Series Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to all Cessna Aircraft Company (Cessna) 180, 182, and 185 series airplanes that have wing extension supplemental type certificate (STC) SA00276NY or supplemental type approval (STA) SA93-136 incorporated. This AD requires inspecting between wing station (W.S.) 90 and W.S. 110 for an angle stiffener at the lower wing spar splice. If the angle stiffener is not installed, this AD requires installing a reinforcing strap. This AD is the result of failed test results revealing that the wings of these Cessna airplanes, without the stiffener, do not meet the applicable design requirements after being modified by the above STC. The actions specified by this AD are intended to prevent wing failure during flight caused by the absence of an angle stiffener, which could cause loss of control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Model 182S Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to all Cessna Aircraft Company (Cessna) Model 182S airplanes. This AD requires repetitively inspecting all engine exhaust muffler end plates (four total) for cracks and replacing any muffler where an end plate is found cracked. The AD also requires fabricating and installing a placard that specifies immediately inspecting all engine exhaust muffler end plates any time the engine backfires upon start-up. This AD is the result of incidents where cracks were found in an engine exhaust muffler end plate on several of the affected airplanes. These cracks were caused by high stresses imposed on the attachment of the exhaust at the area of the firewall. The actions specified by this AD are intended to detect and correct damage to the engine exhaust mufflers caused by such high stress and cracking, which could result in exhaust gases entering the airplane cabin with consequent crew and passenger injury.

Airworthiness Directives; Cessna Aircraft Company Model 182S Airplanes

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 98-01-14, which was sent previously to all known U.S. owners and operators of Cessna Aircraft Company (Cessna) Model 182S airplanes. This AD requires replacing the left and right Aeroquip engine exhaust mufflers (P/N 71379-1254017-8) with an FAA-approved equivalent part. Reports of carbon monoxide gas entering the cabin heating system and the cabin of the Cessna Model 182S airplanes prompted this action. This condition, if not corrected, could result in passenger and pilot injury with consequent loss of control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Models 172R and 182S Airplanes

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 98-01-01, which was sent previously to all known U.S. owners and operators of certain Cessna Aircraft Company (Cessna) Models 172R and 182S airplanes. This AD requires fabricating and installing placards to prohibit operation in instrument flight rules (IFR) conditions and use of the alternate static air source; inspecting the alternate static air source valve to assure that the alternate static air source port is not restricted by the identification placard and to assure that the valve body does not separate from the valve flange; and reworking or replacing as necessary. The AD was the result of reports of improper installation of the identification placard on the alternate static air source. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control of the airplane.