Cessna 208 Caravan

Airworthiness Directives; Textron Aviation, Inc. Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Textron Aviation Inc. (Textron) (type certificate previously held by Cessna Aircraft Company) Models 208 and 208B airplanes. This AD was prompted by reports of loose elevator torque tube attach fasteners. This AD requires repetitively inspecting the inboard and outboard elevator torque tube attachments for loose or incorrectly installed fasteners, replacing all fasteners if loose or incorrectly installed fasteners are found, and reporting the inspection results to the FAA. This AD also includes optional actions to terminate the repetitive inspections. The FAA is issuing this AD to address the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. This AD requires you to measure the roll and the yaw bridle cable tension (adjusting as necessary) and to torque the clamp screws. This AD results from two reported incidences of slack bridle cables with the swaged balls unseating from their drum recesses. We are issuing this AD to detect and correct loose bridle cable clamps, which could result in the swaged ball unseating from the recess in the servo drum and contacting the cable guard pin. This failure could lead to very limited control of the rudder and/or aileron with consequent loss of control.

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. This AD requires you to modify the aileron carry-through cable attachment to the aileron upper quadrant with parts of improved design. This AD results from reports of a "catch" in the aileron control system when the control yoke is turned. We are issuing this AD to prevent the cable attach fitting on the aileron upper quadrant assembly from rotating and possibly contacting or interfering with the aileron lower quadrant assembly, which could result in limited roll control and reduced handling capabilities.

Airworthiness Directives; Cessna Aircraft Company 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 Series Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD also requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of airplanes found with alternate static air source selector valve port obstruction caused by improper installation of the part number identification placard. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. This AD requires you to inspect the left and right wing wire bundle(s) and repair or replace damaged wire. This AD also requires inspecting the wire bundles for correct attachment to the anchor points and correcting any deficient attachments. This AD results from chafed wiring found on wire bundles in the left and right wings containing the auto-control wing de-ice system, fuel quantity indication, and low fuel annunciation on the Cessna 208B airplanes. Improper installation of wire bundle supporting hardware can cause chafed wiring in the affected bundles. We are issuing this AD to detect and correct damaged wiring of the auto- control wing de-ice system, fuel quantity indication, and low fuel annunciation systems. This condition could result in incorrect fuel quantity indications, loss of low fuel quantity annunciations, or loss of the autocontrol wing de-ice system.

Airworthiness Directives; Cessna Aircraft Company 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 Series Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of improper installation of the part number identification placard on the alternate static air source selector valve. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

The FAA is adopting a new airworthiness directive (AD) to supersede AD 2006-06-06, which applies to certain Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. AD 2006-06-06 currently requires you to incorporate information into the applicable section of the Airplane Flight Manual (AFM) and Pilot's Operating Handbook (POH) and requires you to install placards. Since we issued AD 2006-06-06, Cessna issued new S1 Known Icing Equipment AFM supplements and developed a low airspeed awareness system. Consequently, this AD requires you to incorporate the applicable AFM supplement revision and temporarily retain the requirements of AD 2006-06-06 until the above revisions are incorporated. One of the AFM requirements is the installation of a functional low airspeed awareness system to operate the airplane in known icing conditions. We are issuing this AD to assure that the pilot has enough information and the necessary equipment to prevent loss of control of the airplane while in-flight during icing conditions.

Airworthiness Directives; The Cessna Aircraft Company Models 208 and 208B Airplanes

The FAA adopts a new airworthiness directive (AD) for all The Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. This AD requires you to install the pilot assist handle (part number (P/N) SK208-146-2) (or FAA-approved equivalent part number) and deicing boots on the cargo pod and landing gear fairings (part number (P/N) AK208-6C) (or FAA-approved equivalent part number); and make changes to the Pilot's Operating Handbook (POH) and FAA-approved Airplane Flight Manual (AFM). This AD results from reports of several accidents involving the affected airplanes during operations in flight and in ground icing conditions. We are issuing this AD to provide a safe method to detect ice, snow, frost, or slush adhering to the upper wing (a critical surface) prior to takeoff; and to reduce drag in-flight by shedding ice on the cargo pod and landing gear fairings. Ice adhering to the upper wing surface, cargo pod, or landing gear fairings could result in a reduction in airplane performance with the consequences that the airplane cannot perform a safe takeoff or climb.

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

The FAA supersedes Airworthiness Directive (AD) AD 2002-22-17, which applies to all Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes; and AD 2003-21-04, which applies to certain Cessna Models 208 and 208B airplanes. This AD requires you to repetitively inspect the flap bellcranks for cracks and eventually replace these bellcranks. The installation of a newly designed bellcrank to increase the life limits is terminating action for the repetitive inspections. This AD is the result of these developments: Since FAA issued AD 2002- 22-17 and AD 2003-21-04, Cessna designed a new flap bell crank with a life limit of 40,000 landings instead of 7,000 landings. Also, FAA has done more analysis and examination of cracks and missing/incomplete welds in all of the bell cranks. This failure could lead to damage to the flap system and surrounding structure and result in reduced or loss of control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. This AD requires you to inspect any upper and lower wing strut attach fitting nut for existence of the corresponding cotter pin and do any necessary corrective action. This AD is the result of a report of one airplane having loose and improperly tied nuts on the wing struts upper attachment bolts. We are issuing this AD to detect and correct loose and improperly tied nuts on the wing struts, which could result in an attachment nut coming off the bolt. This could lead to the failure of the wing structure with consequent loss of control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Models 208, 208A, 208B, 425, and 441 Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to all Cessna Aircraft Company (Cessna) Models 208, 208A, 208B, 425, and 441 airplanes. This AD requires amending the Limitations Section of the airplane flight manual (AFM) to prohibit the positioning of the power levers below the flight idle stop while the airplane is in flight. This AFM amendment will include a statement of consequences if the limitation is not followed. This AD results from numerous incidents and five documented accidents involving airplanes equipped with turboprop engines where the propeller beta was improperly utilized during flight. The actions specified by this AD are intended to prevent loss of airplane control or engine overspeed with consequent loss of engine power caused by the power levers being positioned below the flight idle stop while the airplane is in flight.

Airworthiness Directives; Cessna Aircraft Company 100, 200, 300, and 400 Series Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to Cessna Aircraft Company (Cessna) 100, 200, 300, and 400 series airplanes. This action requires checking the airplane maintenance records for any fuel, oil, or hydraulic hose, Cessna part number (P/N) S51-10, replaced between March 1995 and February 3, 1997 (the effective date of this AD); immediately checking any of these hoses for a diagonal or spiral external reinforcement wrap; and immediately replacing any of these hoses that have a diagonal or spiral external reinforcement wrap with one that has a criss-cross external reinforcement wrap. This action was prompted by reports of operators experiencing a loss of engine power because of low fuel feed, in addition to Cessna discovering that the rubber hose installed at the factory on certain Cessna Models 208 and 208B airplanes was defective. The Cessna P/N S51-10 rubber hose is utilized on fuel, oil, and hydraulic hoses on the affected airplanes. The actions specified by this AD are intended to prevent fuel, oil, or hydraulic systems failure caused by a collapsed hose.

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to all Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. This action requires revising the Airplane Flight Manual (AFM) to provide the flight crew with recognition cues for, and procedures for exiting from, severe icing conditions, and to limit or prohibit the use of various flight control devices. This amendment is prompted by results of a review of the requirements for certification of the airplane in icing conditions, new information on the icing environment, and icing data provided currently to the flight crews. The actions specified by this AD are intended to minimize the potential hazards associated with operating the airplane in freezing rain or freezing drizzle conditions by providing more clearly defined procedures and limitations associated with such conditions.