Cessna 172

Airworthiness Directives; Textron Aviation Inc. Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Textron Aviation Inc. (Textron) Model 172N, 172P, 172Q, 172RG, F172N, F172P, FR172K, R172K, 182E, 182F, 182G, 182H, 182J, 182K, 182L, 182M, 182N, 182P, 182Q, 182R, T182, F182P, F182Q, FR182, R182, TR182, 206, P206, P206A, P206B, P206C, P206D, P206E, TP206A, TP206B, TP206C, TP206D, TP206E, U206, U206A, U206B, U206C, U206D, U206E, U206F, U206G, TU206A, TU206B, TU206C, TU206D, TU206E, TU206F, TU206G, 207, 207A, T207, T207A, 210-5 (205), 210-5A (205A), 210B, 210C, 210D, 210E, 210F, and T210F airplanes. This AD was prompted by cracks found in the lower area of the forward cabin doorpost bulkhead. This AD requires repetitively inspecting the lower area of the forward cabin doorposts at the strut attach fitting for cracks and repairing any cracks. The FAA is issuing this AD to address the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company Airplanes

We are superseding AD 2000-04-01 that applies to certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H airplanes. AD 2000-04-01 currently requires an inspection of the engine oil pressure switch and, if applicable, replacement of the engine oil pressure switch. This AD increases the applicability of the AD, places a life-limit of 3,000 hours time-in- service on the engine oil pressure switch, and requires replacement when the engine oil pressure switch reaches its life limit. This AD was prompted by new reports of internal failure of the engine oil pressure switch, which could result in complete loss of engine oil with consequent partial or complete loss of engine power or fire. We are issuing this AD to correct the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company Models 172R and 172S airplanes. This AD was prompted by reports of chafing of a new configuration of the fuel return line assembly, which was caused by the fuel return line assembly rubbing against the right steering tube assembly during rudder pedal actuation. This AD requires you to install the forward and aft fuel return line support clamps and brackets; inspect for a minimum clearance between the fuel return line assembly and the steering tube assembly and clearance between the fuel return line assembly and the airplane structure; and, if any damage is found, replace the fuel return line assembly. We are issuing this AD to correct the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company Models 172R and 172S airplanes. This AD was prompted by reports of chafed fuel return line assemblies, which were caused by the fuel return line assembly rubbing against the right steering tube assembly during full rudder pedal actuation. This AD requires you to inspect the fuel return line assembly for chafing; replace the fuel return line assembly if chafing is found; inspect the clearance between the fuel return line assembly and both the right steering tube assembly and the airplane structure; and adjust as necessary. We are issuing this AD to correct the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company Airplanes

We are superseding an existing airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 172R and 172S airplanes. That AD currently requires you to inspect the fuel return line assembly for chafing; replace the fuel return line assembly if chafing is found; and inspect the clearance between the fuel return line assembly and both the right steering tube assembly and the airplane structure, adjusting as necessary. Since we issued that AD, we have received a field report of a fuel return line chafing incident on a Cessna Model 172 airplane with a serial number (S/N) that was not included in the AD. This AD retains the actions of the current AD and adds S/Ns to the Applicability section of the AD. Chafing of the fuel return line assembly could lead to fire. This new AD requires the actions of the current AD and adds S/Ns to the Applicability section of the AD. We are issuing this AD to correct the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company Models 150, 152, 170, 172, 175, 177, 180, 182, 185, 188, 190, 195, 206, 207, 210, T303, 336, and 337 Airplanes

We are superseding an existing airworthiness directive (AD) for Cessna Aircraft Company (Cessna) 150, 152, 170, 172, 175, 177, 180, 182, 185, 188, 190, 195, 206, 207, 210, T303, 336, and 337 series airplanes. That AD currently requires repetitive inspections and replacement of parts, if necessary, of the seat rail and seat rail holes; seat pin engagement; seat rollers, washers, and axle bolts or bushings; wall thickness of roller housing and the tang; and lock pin springs. This new AD requires retaining all of the actions from the previous AD and adding steps to the inspection procedures in the previous AD. This AD was prompted by added steps to the inspection procedures, added revised figures, and clarification of some of the existing steps. We are issuing this AD to prevent seat slippage or the seat roller housing from departing the seat rail, which may consequently cause the pilot/copilot to be unable to reach all the controls. This failure could lead to the pilot/copilot losing control of the airplane.

Airworthiness Directives; Cessna Aircraft Company (Cessna) Model 172 Airplanes Modified by Supplemental Type Certificate (STC) SA01303WI

We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires installing a full authority digital engine control (FADEC) backup battery, replacing the supplement pilot's operating handbook and FAA approved airplane flight manual, and replacing the FADEC backup battery every 12 calendar months. This AD was prompted by an incident where an airplane experienced an in-flight engine shutdown caused by a momentary loss of electrical power to the FADEC. We are issuing this AD to prevent interruption of electrical power to the FADEC, which could result in an uncommanded engine shutdown. This failure could lead to a loss of engine power.

Airworthiness Directives; Cessna Aircraft Company 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 Series Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD also requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of airplanes found with alternate static air source selector valve port obstruction caused by improper installation of the part number identification placard. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Airworthiness Directives; Cessna Aircraft Company 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 Series Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of improper installation of the part number identification placard on the alternate static air source selector valve. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Airworthiness Directives; Cessna Aircraft Company 172, 182, and 206 Series Airplanes

The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 182, and 206 series airplanes. This AD requires you to remove the crew seats, modify the seat base/ back attach brackets, and reinstall the seats of the affected airplanes. This AD results from reports of the seat base/back attach bracket failing where it is welded to the seat base. We are issuing this AD to prevent failure of the seat base/back attach brackets, which could result in the seats collapsing backwards during flight with consequent loss of control.

Airworthiness Directives; Cessna Aircraft Company Models 172R and 172S Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 172R and 172S airplanes. This AD requires you to inspect the fuel return line assembly for chafing; replace the fuel return line assembly if chafing is found; and inspect the clearance between the fuel return line assembly and both the right steering tube assembly and the airplane structure, adjusting as necessary. This AD results from reports of chafed fuel return line assemblies, which were caused by the fuel return line assembly rubbing against the right steering tube assembly during full rudder pedal actuation. We are issuing this AD to detect and correct chafing of the fuel return line assembly, which could result in fuel leaking under the floor and fuel vapors entering the cabin. This condition could lead to fire under the floor or in the cabin area.

Airworthiness Directives; Cessna Aircraft Company 172 and 182 Series Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company 172 series airplanes with the BRS-172 Parachute System installed via Supplemental Type Certificate (STC) No. SA01679CH and Cessna Aircraft Company 182 series airplanes that are equipped with the BRS-182 Parachute System installed via STC No. SA01999CH. This AD requires you to replace the pick-up collar support and nylon screws for the BRS-172 and BRS-182 Parachute System. This AD results from notification by Ballistic Recovery Systems, Inc. (BRS) that the pick-up collar assembly may prematurely move off the launch tube and adversely affect rocket trajectory during deployment. We are issuing this AD to prevent premature separation of the collar, which could result in the parachute failing to successfully deploy.

Airworthiness Directives; Cessna Aircraft Company Models 172R, 172S, 182T, T182T, 206H, and T206H Airplanes

The FAA is adopting a new airworthiness directive (AD) to supersede AD 2006-17-04, which applies to certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. AD 2006-17-04 currently requires you to inspect the two end fittings on each of the flexible fuel hoses located in the engine compartment for the correct torque values, and, if any incorrect torque values are found during the inspection, tighten the hose end fittings to the correct torque values. This AD results from four reports of loose fuel lines connected to the fuel servo or fuel flow transducer. Two reports were of in-flight engine failure on a Model T182T airplane. A third report was of in-flight engine failure on a Model 206H airplane. A fourth report was of a Model 172S airplane losing engine power on final approach. Consequently, this AD would require you to establish the correct torque values of the end fittings on fuel hoses for certain Cessna Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. This AD clarifies that the torque values need to be physically established and visual inspection only is not sufficient. We are issuing this AD to detect and correct potential loss of fuel flow, which may result in partial or complete loss of engine power and/or uncontrolled engine compartment fire due to fuel leakage forward of the firewall.

Airworthiness Directives; Cessna Aircraft Company Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H Airplanes

The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H airplanes. This AD requires you to install Modification Kit MK172-25-10C or a steel lock rod/bar on both crew seat back cylinder lock assemblies. If a steel lock rod/bar has already been installed on the crew seat back cylinder lock assembly, no further action is required. If you have already installed Modification Kit MK172-25-10A or MK172-25-10B, this AD requires you to do an installation inspection and correct any discrepancies found. This AD results from reports of the crew seat back cylinder lock assembly failing at the aft end and other cylinder lock assemblies found cracked. We are issuing this AD to prevent the crew seat back cylinder lock assembly from bending, cracking, or failing. This failure could cause uncontrolled movement of the seat back, resulting in possible backward collapse during flight. Backward collapse of either crew seat back could result in an abrupt pitch-up if the affected crew member continues to hold on to the control yoke during this failure and could cause difficulty in exiting the airplane from an aft passenger seat after landing.

Airworthiness Directives; Cessna Aircraft Company Models 172R, 172S, 182T, T182T, 206H, and T206H Airplanes

The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. This AD requires you to inspect any MC01-3A I.C. 9 or MC01-3A I.C. 10 main electrical power junction box circuit breakers for correct amperage (amp) (a correct 40-amp circuit breaker) and replace any incorrect amp circuit breaker with the correct 40-amp circuit breaker. This AD results from several reports of circuit breakers that are not the correct 40-amp circuit breaker installed in the MC01-3A main electrical power junction box. We are issuing this AD to replace any incorrect circuit breaker installed in the MC01-3A I.C. 9 or MC01-3A I.C. 10 main electrical power junction box, which could result in premature tripping of the power junction box main feeder circuit breakers and could lead to partial or complete loss of all electrical power on the airplane. This condition could lead to the loss of all navigation and communication equipment and lighting in the cockpit.

Airworthiness Directives; The Cessna Aircraft Company Models 172R, 172S, 182T, and T182T Airplanes

The FAA is adopting a new airworthiness directive (AD) to revise emergency AD 2005-05-53 for The Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, and T182T airplanes. This AD contains the same information as emergency AD 2005-05-53 R1 and publishes the action in the Federal Register. It requires you to do a one-time detailed inspection of the flight control system, correct installations that do not conform to type design, and repair any damage. This AD is the result of flight control system problems found on airplanes within Cessna's control that could also exist on airplanes produced and delivered within a certain time period. We are issuing this AD to prevent loss of airplane control due to incorrect or inadequate rigging of critical flight systems.

Airworthiness Directives; Cessna Aircraft Company 120, 140, 140A, 150, F150, 170, 172, F172, FR172, P172D, 175, 177, 180, 182, 185, A185E, 190, 195, 206, P206, U206, TP206, TU206, 207, T207, 210, T210, 336, 337, and T337 Series Airplanes

The FAA adopts a new airworthiness directive (AD) that will supersede AD 86-26-04, which applies to certain Cessna Aircraft Company (Cessna) 120, 140, 140A, 150, F150, 170, 172, F172, FR172, P172D, 175, 177, 180, 182, 185, A185E, 190, 195, 205, 205A, 206, P206, P206E, TP206A, TU206, TU206E, U206, U206E, 207, T207, 210, T210, 336, 337, and T337 series airplanes. AD 86-26-04 currently requires you to inspect and, if necessary, modify the pilot/co-pilot upper shoulder harness adjusters that have certain Cessna accessory kits incorporated. This AD is the result of reports that additional airplanes have the same unsafe condition and the manufacturer revised the service information to add these airplanes and correct the part number of the shoulder harness adjusters. Consequently, this AD retains the actions of 86-26-04, adds additional airplanes to the applicability section of this AD, and incorporates the revised service information. We are issuing this AD to prevent slippage of the pilot/co-pilot shoulder harness, which could result in failure of the shoulder harness to maintain proper belt length adjustment and tension. Such failure could result in pilot/co- pilot injury.

Airworthiness Directives; Cessna Aircraft Company Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H Airplanes

The FAA supersedes Airworthiness Directive (AD) 2003-24-13, which applies to certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H airplanes that are equipped with a certain Honeywell KAP 140 autopilot computer system installed on the center instrument control panel near the throttle. AD 2003-24-13 currently requires you to install an update to the operating software of certain KAP 140 autopilot computer system, change the unit's part number, and change the software modification identification tab. This AD is the result of the FAA inadvertently omitting four affected Honeywell KAP 140 autopilot computer system part numbers and an affected airplane serial number from the applicability section of AD 2003-24-13. This AD retains the actions required in AD 2003-24-13, corrects the applicability section, and incorporates a revised installation bulletin issued by Honeywell.

Airworthiness Directives; Cessna Aircraft Company Models 172N, 172P, R172K, 172RG, F172N, F172P, FR172J, and FR172K Airplanes

This amendment supersedes Airworthiness Directive (AD) 80-04- 08, which requires inspecting (one-time) the fuel line and map light switch in the left hand forward door post for chafing or arcing on certain Cessna Aircraft Company (Cessna) Model 172N, R172K, F172N, and FR172K airplanes and repairing any damage found. AD 80-04-08 also requires providing at least a 0.50-inch clearance between the map light switch and the fuel line; and installing a switch cover (insulator) over the map light switch. This AD requires you to extend the inspections and installation of the switch cover requirement to certain 172N, 172P, R172K, 172RG, F172N, F172P, FR172J, and FR172K series airplanes. This AD also requires replacement of the fuel line, if damaged; and makes the switch cover inspection and replacement repetitive. This AD is the result of FAA receiving several reports of incidents of electrical shorts on Cessna Model 172N airplanes. The actions specified by this AD are intended to detect and correct any chafing between the map light switch and the bordering fuel line, which could result in a fuel leak and an in-flight fire.

Airworthiness Directives; Cessna Aircraft Company Models 172R and 172S Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to certain Cessna Aircraft Company (Cessna) Models 172R and 172S airplanes. This AD requires a one-time inspection for proper engine idle speed and fuel control mixture setting and adjustment, as necessary. This AD also requires incorporating engine operating procedures into the pilots operating handbook (POH) and FAA-approved airplane flight manual (AFM). This AD is the result of reports of rough engine operation because of an over-rich fuel mixture (improper fuel flow settings). The actions specified by this AD are intended to detect and correct such improper fuel flow settings, which could result in rough engine operation or engine stoppage. This over-rich fuel mixture also contributes to the engine not restarting during flight when using published in-flight restart procedures.

Airworthiness Directives; Cessna Aircraft Company Model 172RG Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to certain Cessna Aircraft Company (Cessna) Model 172 airplanes. This AD requires you to inspect the main landing gear pivot assemblies for cracks, replace any cracked main landing gear pivot assemblies, and install new bushings on the pivot assembly shaft. This AD is the result of many service difficulty reports of cracked main landing gear pivot assemblies on the affected airplanes. The actions specified by this AD are intended to detect, correct, and prevent future cracks on the original design landing gear pivots. Cracked main landing gear pivots could fail resulting in gear-up landings or loss of braking.

Airworthiness Directives; Cessna Aircraft Company 150, 152, 172, 177, 180, 182, 185, 188, 206, 207, 210, and 337 Series Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to Cessna Aircraft Company (Cessna) 150, 152, 172, 177, 180, 182, 185, 188, 206, 207, 210, and 337 series airplanes. This AD requires measuring the visible length of standpipe (tube) in the top assembly of the fuel strainer assembly for the correct length, and replacing any fuel strainer assembly that does not have the correct length of standpipe. This AD is the result of reports that the fuel strainer assemblies on the affected airplanes were manufactured with the fuel standpipes incorrectly installed in the assembly housing top. The actions specified by this AD are intended to prevent foreign material from entering the fuel system and engine, which could result in loss of engine power or complete engine stoppage during flight.

Airworthiness Directives; Cessna Aircraft Company 170, 172, 175, and 177 Series Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to all Cessna Aircraft Company (Cessna) 170, 172, 175, and 177 series airplanes. This AD requires replacing certain fuel selector valve cams or fuel selector valves that Cessna shipped from December 6, 1998, through May 10, 1999, and prevents the future installation of these fuel selector valve cams or fuel selector valves. This AD allows the pilot to check the logbooks to determine whether one of these fuel selector valve cams or fuel selector valves is installed. This AD results from reports from Cessna that fuel selector valve cams and fuel selector valves were manufactured with control shafts that will not allow both tanks to supply fuel to the engine in certain situations. The actions specified by this AD are intended to prevent an inadequate supply of fuel from reaching the engine because of a fuel selector valve cam or fuel selector valve. This could result in an emergency landing or loss of control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Model 172R Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to Cessna Aircraft Company (Cessna) Model 172R airplanes equipped with a certain modification kit that reduces friction in the elevator control system. This AD requires inspecting the control yoke pivot bolt to assure positive clearance between the pivot bolt's threaded end and aileron direct cable. If positive clearance is not found, this AD requires replacing the control yoke pivot bolt, inspecting the adjacent aileron control cables for damage, and replacing any damaged aileron control cable. This AD is the result of the manufacturer supplying incorrect length control yoke pivot bolts in Cessna Modification Kits MK 172-27-01 that were shipped from September 21, 1998, through April 18, 1999. The actions specified by this AD are intended to prevent failure of an aileron control cable because of an incorrect length control yoke pivot bolt rubbing on one of these cables, which could result in loss of aileron control with loss of directional control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Model 172R Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to certain Cessna Aircraft Company (Cessna) Model 172R airplanes that are not equipped with an autopilot. This AD requires inspecting the right wing for an incorrectly routed, frayed, or damaged aileron control cable, and re-routing any incorrectly routed cable or replacing any frayed or damaged cable. The AD also requires reporting any incorrectly routed, frayed, or damaged cable to the Federal Aviation Administration (FAA). This AD is the result of a report of an incorrectly routed aileron control cable in the right wing of an airplane of the same type design to those affected by this AD. The cable was routed over the aileron auto pilot actuator pulley and the cable was rubbing on the cable guard. The actions specified by this AD are intended to prevent loss of aileron control caused by a damaged or frayed aileron control cable, which could result in loss of directional control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Model 172R Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to certain Cessna Aircraft Company Model 172R airplanes. This AD requires modifying the lower forward doorpost bulkhead by installing rivets. This AD is the result of a report from the manufacturer that these rivets were erroneously omitted during manufacture of some of the new production airplanes. The actions specified by this AD are intended to prevent reduced structural rigidity at the forward doorpost bulkhead, which could result in structural cracking and possible loss of control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Model 172R Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to certain Cessna Aircraft Company (Cessna) Model 172R airplanes. This action requires: inspecting for incorrectly routed aileron control cables in the center console area; inspecting for incorrectly routed aileron control cables in the right-hand (RH) wing area; inspecting for a loose or improperly installed center lock clamp on the forward aileron control cable drum; and inspecting for loose or missing elevator trim actuator mounting screws, loose rudder circuit pulleys, missing rudder cable guard pins, incorrect elevator trim cable routing, aileron control cable clearance, and flight control cable tension or rigging outside specification. If any of the above conditions are found, this AD requires correcting, repairing, or replacing any damaged or missing part, and reporting any of the above conditions found to the Wichita Aircraft Certification Office. Notification by the manufacturer, service difficulty reports (SDR's), and an FAA surveillance audit at the manufacturing facility identifying potential deficiencies on the affected airplanes prompted the action. The actions specified by this AD are intended to prevent loss of aileron and elevator control, which could result in loss of directional control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Model 172R Airplanes

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 98-02-05, which was sent previously to all known U.S. owners and operators of Cessna Aircraft Company (Cessna) Model 172R airplanes. This AD requires de-activating the cabin heating system until the engine exhaust muffler can be replaced, and fabricating and installing a placard within the pilot's clear view, using \1/8\-inch letters with the following words: ``CABIN HEATER INOPERATIVE.'' Inadequate or failed weldments that are leaking exhaust gas (including carbon monoxide) from the muffler into the airplane's cabin and cockpit area prompted this action. The actions specified by this AD are intended to prevent carbon monoxide gas from entering the airplane's cabin heating system and cabin, which, if not corrected, could result in passenger and pilot injury with consequent loss of control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Models 172R and 182S Airplanes

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 98-01-01, which was sent previously to all known U.S. owners and operators of certain Cessna Aircraft Company (Cessna) Models 172R and 182S airplanes. This AD requires fabricating and installing placards to prohibit operation in instrument flight rules (IFR) conditions and use of the alternate static air source; inspecting the alternate static air source valve to assure that the alternate static air source port is not restricted by the identification placard and to assure that the valve body does not separate from the valve flange; and reworking or replacing as necessary. The AD was the result of reports of improper installation of the identification placard on the alternate static air source. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control of the airplane.

Airworthiness Directives; Cessna Aircraft Company Model 172R Airplanes

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 97-12-06, which was sent previously to known U.S. owners and operators of certain Cessna Aircraft Company (Cessna) Model 172R airplanes. This AD requires checking the clearance between both the gascolator and cowling area and the tailpipe and cowling area, and modifying these areas immediately if any evidence of rubbing at either location is found or modifying the gascolator to cowling area within a certain time period if no evidence of rubbing at either location is found. This AD results from an occurrence of fuel loss on a Cessna Model 172R airplane, which was severe enough to force an emergency landing. Investigation of the occurrence reveals that the cowling knocked the gascolator drain valve off the gascolator. The actions specified by this AD are intended to prevent the cowling from rubbing against the gascolator drain valve or the tailpipe, which could result in fuel loss and engine stoppage.

Airworthiness Directives; Brackett Aircraft Company, Inc. Air Filter Assemblies Installed on Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to airplanes with certain Brackett Aircraft Company, Inc. (Brackett) air filter assemblies that have a neoprene gasket design installed between the carburetor heat box and the air filter frame. This action requires repetitively inspecting (visually) the air filter frame for a loose or deteriorating gasket, and replacing any gasket found loose or deteriorated. An accident report concerning a Cessna Model 172 airplane that experienced engine loss because a six-inch piece of neoprene gasket material was lodged in the carburetor prompted this action. The actions specified by this AD are intended to prevent gasket particles from entering the carburetor because of air filter gasket failure, which could result in partial or complete loss of engine power.