Cessna 340

Airworthiness Directives; Textron Aviation, Inc. Airplanes

We are superseding Airworthiness Directive (AD) 2016-07-24 for all Textron Aviation, Inc. Models 310 through 310R, E310H, E310J, T310P through T310R, 310J-1, 320 through 320F, 320-1, 335, 340, 340A, 401 through 401B, 402 through 402C, 411, 411A, 414, 414A, and 421 through 421C airplanes (type certificates 3A10, 3A25, and A7CE previously held by Cessna Aircraft Company). AD 2016-07-24 required replacement and repetitive inspections of the hardware securing the elevator trim tab push-pull rod. This AD retains the actions for AD 2016-07-24 but revises the repetitive inspection intervals and allows for a longer bolt for the attachment of the elevator trim tab actuator rod end to the push-pull tube connection and/or for the elevator trim tab horn end to the push-pull tube connection. This AD was prompted by comments indicating difficulties with bolt installation and requesting a revision to repetitive inspection intervals to coincide with established inspection intervals. We are issuing this AD to prevent jamming of the elevator trim tab in a position outside the normal limits of travel due to the loss of the attachment hardware connecting the elevator trim tab actuator to the elevator trim tab push-pull rod, which could result in loss of control.

Airworthiness Directives; Cessna Aircraft Company Airplanes

We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 310, 320, 340, 401, 402, 411, 414, and 421 airplanes. This AD was prompted by an investigation of recent and historical icing-related accidents and incidents for the products listed above. This AD requires either having the supplemental airplane flight manual/airplane flight manual supplement (SAFM/AFMS) inside the airplane and accessible to the pilot during the airplane's operation or installing a placard that prohibits flight into known icing conditions and installing a placard that increases published airspeed on approach at least 17 mph (15 knots) in case of an inadvertent encounter with icing. We are issuing this AD to correct the unsafe condition on these products.

Airworthiness Directives; Cessna Aircraft Company 300 and 400 Series Airplanes

This amendment supersedes Airworthiness Directive (AD) 75-23- 08 R5, which currently requires repetitively inspecting and replacing or repairing the exhaust system on certain Cessna Aircraft Company (Cessna) 300 and 400 series airplanes. The requirements of this AD replace the inspections and replacements that are required by AD 75-23- 08 R5 with inspections and replacements containing new simplified procedures for all 300 and 400 series airplanes (models affected by the current AD plus additional models). This AD also revises the inspection intervals and requires replacing certain unserviceable parts and removing the exhaust system for a detailed inspection. This AD is the result of numerous incidents and accidents relating to the exhaust systems on Cessna 300 and 400 series airplanes dating from the middle 1970's to the present, including six incidents since issuance of AD 75- 23-08 R5 where exhaust problems were cited. The actions specified by this AD are intended to detect and correct cracks and corrosion in the exhaust system, which could result in exhaust system failure and a possible uncontrollable in-flight fire with pilot and/or passenger injury.

Airworthiness Directives; Cessna Aircraft Company Models 340A and 414A Airplanes

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 98-24-14, which was sent previously to all known U.S. owners and operators of certain Cessna Aircraft Company (Cessna) Models 340A and 414A airplanes that could be equipped with any WYE tube, part number (P/N) 9910299-25 or P/N 9910299-26, in the engine exhaust system. This AD requires removing from service any P/N 9910299-25 or P/N 9910299-26 engine exhaust system WYE tube. The AD resulted from reports of five instances where the engine exhaust components in the WYE tube were manufactured without welds on critical parts that are installed adjacent to the firewall. The actions specified by this AD are intended to detect and correct exhaust leaks caused by nonwelded exhaust system components, which could result in aluminum fuel lines bursting with consequent fuel spillage, an airplane fire, and/or an explosion.

Airworthiness Directives; Cessna Aircraft Company Models T303, 310R, T310R, 335, 340A, 402B, 402C, 404, F406, 414, 414A, 421B, 421C, 425, and 441 Airplanes

This amendment adopts a new airworthiness directive (AD) that applies to Cessna Aircraft Company Models T303, 310R, T310R, 335, 340A, 402B, 402C, 404, F406, 414, 414A, 421B, 421C, 425, and 441 airplanes. This action requires revising the FAA-approved Airplane Flight Manual (AFM) to specify procedures that would prohibit flight in severe icing conditions (as determined by certain visual cues), limit or prohibit the use of various flight control devices while in severe icing conditions, and provide the flight crew with recognition cues for, and procedures for exiting from, severe icing conditions. The proposed AD is prompted by the results of a review of the requirements for certification of these airplanes in icing conditions, new information on the icing environment, and icing data provided currently to the flight crew. The actions specified by this AD are intended to minimize the potential hazards associated with operating these airplanes in severe icing conditions by providing more clearly defined procedures and limitations associated with such conditions.